Industry Three phase AC Induction Brake Electric Motor for Filter Press

The filter press with Industry Three phase AC Induction Brake Electric Motor uses a special filter medium to apply a certain pressure to the object, so that a mechanical device that oozes out the liquid is a commonly used solid-liquid separation device. It was used in chemical production in the early 18th century and is still widely used in chemical, pharmaceutical, metallurgical, dye, food, brewing, ceramics and environmental protection industries.

Industry Three phase AC Induction Brake Electric Motor
Industry Three phase AC Induction Brake Electric Motor

working principle:

The hydraulic compression mechanism of the filter press with Industry Three phase AC Induction Brake Electric Motor consists of a hydraulic station, a cylinder, a piston, a piston rod, and a Hafland card hydraulic station connected to the pressure plate. The motor, the oil pump and the relief valve are adjusted. Valves, pressure gauges, oil circuits, fuel tanks.

Filtration method: The flow of the filtrate is clearly divided into flow filtration and dark flow filtration. For the clear flow filtration, a water nozzle is arranged on the lower liquid outlet of each filter plate, and the filtrate flows out intuitively from the water nozzle. Under the dark flow filtration, a liquid outlet hole is arranged below each filter plate, and the liquid outlet holes of the plurality of filter plates are connected into one liquid outlet passage, which is discharged by a pipe connected by the liquid outlet hole below the thrust plate.

Washing method: When the filter cake needs to be washed, it sometimes flows in one-way washing and two-way washing, undercurrent one-way washing and two-way washing.

Industry Three phase AC Induction Brake Electric Motor
Industry Three phase AC Induction Brake Electric Motor

Installation and commissioning:

  1. Thefilter press with Industry Three phase AC Induction Brake Electric Motor  should be installed on a flat concrete foundation. The thrust plate foot of the feeding end is fixed on the foundation by the anchor bolt; the bracket end does not need the anchor bolt, or the anchor bolt is positioned and locked with two nuts, and a proper gap is left between the nut gasket and the foot base, The machine feet can be slightly stretched. The installer should correct the verticality of the beam and the large plane of the thrust plate before positioning.
  2. The foundation structure should be designed by the construction engineering personnel according to the equipment load condition, and the anchor bolts should be filled twice with the reserved hole position.
  3. There should be sufficient operation and maintenance space around the filter presswithIndustry Three phase AC Induction Brake Electric Motor . The hydraulic pressure filter press should select the appropriate position to place the hydraulic station to ensure that the hydraulic station can work normally.
  4. Place the filter plate according to the work requirements and arrange the feeding, washing and draining lines. It is equipped with a filtered pressure display and a return channel that controls the filtration pressure. In the case of a diaphragm squeeze type, a compressed air line is arranged.

5.Hydraulic filter press with Industry Three phase AC Induction Brake Electric Motor , hydraulic station fuel tank into the clean 20 #-40 # hydraulic mechanical oil, the use of temperature >-5 ° C; if the ambient temperature is low, you can choose a similar viscosity, low freezing point hydraulic oil. Hydraulic oil must be added via an 80-100 mesh screen.

6, mechanical or hydraulic compression device, the power to start the motor should work correctly. When the hydraulic pressure is pressed and pressurized, the pressure gauge should rise steadily, and the hydraulic system should have no leakage. The working pressure of the hydraulic station should be adjusted according to the size of the model. If the oil tank is found to be insufficient after the test, it must be replenished.

 

 

With Best Regards,

Cherry Zhang ( Sales Department; Miss. )   

NER GROUP CO.,LIMITED

Yantai Bonway Manufacturer Co., Ltd                                      

Tel:+86-535-6330966

Mobile:+86-18865558975

http://www.bonwaygroup.com

https://twitter.com/gearboxmotor

https://www.facebook.com/sogears1993

Viber/Line/Whatsapp/Wechat: 008618865558975   

E-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.; Skepy ID:live:cherry_3053

Add:No.5 Wanshoushan Road Yantai city Shandong Province, China

YGP Series Roller Track Frequency Control Electric...
ZQ cylindrical gear reducer,gearbox motor manufact...
 

Comments

No comments made yet. Be the first to submit a comment
Guest
Friday, 29 March 2024

Captcha Image

By accepting you will be accessing a service provided by a third-party external to https://www.guomaodrive.com/

Contact Us Now!

NER GROUP CO.,LIMITED

Yantai Bonway Manufacturer Co., Ltd

Tel:+86-535-6330966

Mobile:+86-18563806647

Whatsapp/Wechat: 008618563806647

https://twitter.com/gearboxmotor

https://www.facebook.com/sogears1993

https://www.youtube.com/c/Gearmotors

E-mail:inquiry@sogears.com; Skype ID: qingdao411

Industrial gearbox manufacturer in China

As a Industrial gearbox manufacturer in China, We offer the international standard high quality gear speed reducer and reduction gearbox who has the big stock house to guarantee the prompt delivery Depending on the professional industry field solution, excellent industry field achievement and the leading technology application in Hoist&Crane, Sugar&Paper, Coal&Mining, Rubber&Plastic, Packing&Conveyors, Energy&Fans&Pumps, Cement&Construction, Sawmills&Wood Mills, Food&Butchering&Pharma, Chemical&Boilers&Ceramic, Recycling&Sewage disposal, Steel&Rolling Mill&Metallurgy, Textile&Ginning&Leather working and so on.